Back to products
A-FAZR0030Category D
PP Impact & Weld-Line Modifier
Eliminates brittle failure in PP under mechanical stress and reinforces critical weld lines.
Polypropylene RoHS TDS
Logistics & Documentation
Plastic-Pallet Option · Import Documentation Support
- Lead Time: Depends on supplier stock, production schedule, shipping route and destination. GTA dispatch typically targets 24–48 hours on confirmed stock items.
- Packaging Option: Injection-molded plastic pallets available on request as an alternative to wooden pallets, subject to supplier capability and order size.
- Documentation Support: Import documentation support available. Available documents may include TDS, SDS, COA, origin documents and compliance declarations where applicable.
Technical Data Sheet
TDS · A-FAZR0030
Product form
Pellets (cylindrical, 2–4 mm)
Appearance
White
Carrier / matrix
Polypropylene compatible base resin
Key Physical & Chemical Properties
| Active ingredient | 20 – 40 % concentrate |
|---|---|
| Bulk density | 0.95 – 1.10 g/cm³ |
| Melt Flow Index (190 °C / 2.16 kg) | 5 – 12 g/10 min |
| Moisture content | ≤ 0.10 % |
| Recommended let-down ratio | 1 : 50 to 1 : 200 |
Recommended dosage
0.5 – 3.0 % by weight depending on target performance.
Processing temperature
190 – 260 °C
Packaging
25 kg multi-wall poly-woven bag with PE inner liner, 1000 kg FIBC, or 25 MT FCL bulk.
Shelf life
24 months from production date in unopened original packaging.
Storage
Store dry below 35 °C, away from direct sunlight, ignition sources and incompatible chemicals.
Target Applications
- Blown / cast film and lamination
- Injection molding of automotive and consumer parts
- Pipe, sheet, and profile extrusion
- Wire & cable jacketing where applicable
Key Features
- Long-lasting performance with low dosage
- Compatible with most polyolefin and engineering resins
- Excellent dispersion — no agglomerates
- REACH-registered active components
Safety Data Sheet · GHS / OSHA HazCom / WHMIS 2015
SDS · A-FAZR0030
Signal word
Not classified
Not classified as hazardous under OSHA HazCom 2012 / GHS / WHMIS 2015.
§ 1Identification▾
- Product code
- A-FAZR0030
- Product name
- PP Impact & Weld-Line Modifier
- Product use
- Industrial raw material — Automotive Moldings, Building & Construction.
- Restrictions
- Industrial use only. Not for direct consumer sale unless explicitly labelled food/feed grade.
- Supplier
- Allzone Trading Corp.
- Address
- Ontario, Canada
- Technical contact
- technical@allzonetrading.ca · +1 (437) 297-6255
- Emergency
- CHEMTREC +1 800 424 9300 / CANUTEC +1 613 996 6666
§ 2Hazards Identification▾
- GHS classification
- Not classified as hazardous under OSHA HazCom 2012 / GHS / WHMIS 2015.
- Signal word
- Not classified
- Pictograms
- None required.
- Hazard statements
- No GHS hazard statements apply to this article in supplied form.
- Precautionary statements
- P210 Keep away from heat, sparks, open flames and hot surfaces.
§ 3Composition / Information on Ingredients▾
- Mixture
- Engineered polypropylene based pp impact & weld-line modifier.
- Carrier
- Polypropylene compatible polymer.
§ 4First Aid Measures▾
- Inhalation
- Move to fresh air. Get medical advice if discomfort persists.
- Skin contact
- Wash with soap and water. Get medical advice if irritation persists.
- Eye contact
- Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do.
- Ingestion
- Rinse mouth. Do not induce vomiting. Seek medical advice if discomfort persists.
- Hot melt burns
- For pellet-form products processed at melt temperature: cool affected area with cold water. Do NOT peel solidified polymer from skin — seek medical attention.
§ 5Fire-Fighting Measures▾
- Suitable extinguishing media
- Water spray, dry chemical, CO2, foam.
- Unsuitable media
- None known.
- Special hazards
- Combustion may produce CO, CO2 and dense black smoke. Polymer melt drips during fire.
- PPE for firefighters
- Self-contained breathing apparatus (SCBA) and full protective gear.
§ 6Accidental Release Measures▾
- Personal precautions
- Wear PPE per Section 8. Avoid generating dust. Ventilate area.
- Environmental precautions
- Prevent entry into drains, waterways or soil. Notify authorities if significant release.
- Cleanup
- Sweep or vacuum spilled material into labelled container for recycling or disposal.
§ 7Handling & Storage▾
- Handling
- Handle in well-ventilated areas. Avoid generating dust. Use appropriate PPE.
- Storage
- Store dry below 35 °C, away from direct sunlight and ignition sources.
- Incompatible materials
- Strong oxidizers.
§ 8Exposure Controls / Personal Protection▾
- Engineering controls
- Local exhaust ventilation at material transfer and melt-processing points. Maintain dust below regional OEL.
- Respiratory protection
- Dust mask if fines / dust generated.
- Hand protection
- Heat-resistant gloves when handling molten polymer; cotton gloves for cold pellets.
- Eye protection
- Safety glasses with side shields; chemical splash goggles when handling powders or molten material.
- Body protection
- Long-sleeve work clothing. Full chemical apron for corrosive products.
- Exposure limits
- Follow nuisance-dust limits (10 mg/m³ total, 5 mg/m³ respirable).
§ 9Physical & Chemical Properties▾
- Physical state
- Solid pellets / powder
- Color
- White / off-white / pre-colored
- Odor
- Odorless to faint polymer odor
- pH (1 % solution)
- Not applicable (insoluble)
- Melting / decomposition
- Polymer melt 110 – 250 °C (matrix dependent)
- Flash point
- Not applicable (solid article)
- Solubility (water)
- Insoluble
- Density
- 0.9 – 2.2 g/cm³ depending on grade
§ 10Stability & Reactivity▾
- Stability
- Stable under normal storage and handling conditions.
- Conditions to avoid
- Excessive heat, ignition sources, prolonged UV exposure.
- Hazardous decomposition products
- CO, CO2, polymer fragment volatiles. Azodicarbonamide additionally releases NH3, N2.
§ 11Toxicological Information▾
- Acute oral toxicity (LD50, rat)
- Not classified (> 2000 mg/kg expected)
- Skin irritation
- Not classified for solid article in supplied form.
- Eye irritation
- Mechanical irritation possible from dust.
- Respiratory sensitization
- Not classified.
- Carcinogenicity
- Not classified.
- Mutagenicity / reproductive tox.
- No known effects based on current data.
§ 12Ecological Information▾
- Aquatic toxicity
- Not classified — substance is essentially inert in water.
- Persistence
- Persistent in environment — polymer fragments are not readily biodegradable.
- Bioaccumulation
- No bioaccumulation potential expected.
§ 13Disposal Considerations▾
- Product disposal
- Dispose in accordance with local, provincial, state and federal regulations. Recycle polymer fractions through certified plastic recyclers where possible.
- Packaging disposal
- Recycle empty bags / liners after thorough emptying.
- Waste codes
- Non-hazardous solid waste (EWC 07 02 13 typical).
§ 14Transport Information▾
- Status
- Not regulated for transport under DOT / IATA / IMDG / ADR / TDG.
§ 15Regulatory Information▾
- REACH (EC 1907/2006)
- All components registered or exempt. No SVHC listed above 0.1 % w/w.
- RoHS (EU 2011/65)
- Heavy metals < 1000 ppm (Pb, Hg, Cr⁶⁺) and < 100 ppm (Cd).
- Food contact
- Not intended for food-contact applications.
- WHMIS 2015 (Canada)
- Not classified as a hazardous product.
- TSCA / DSL
- All substances listed on US TSCA and Canadian DSL inventories.
§ 16Other Information▾
- Revision
- Rev. 2026-06-15 (representative industry-standard datasheet).
- Disclaimer
- Information provided in good faith based on current knowledge. No warranty expressed or implied. User is responsible for verifying suitability for end use and compliance with local regulations.
- Document
- SDS for A-FAZR0030
This SDS is provided as representative industry-standard guidance. For project-specific binding documentation, please request the formal current revision via the technical contact above.
Sourcing Support
Need help sourcing this product?
Send us your product name, quantity, application, destination, and required documents. We will review your request and help compare available supply options.
Pricing and availability depend on quantity, destination, supplier confirmation and market conditions.