Applications
Where it is used
- Agricultural films and covers with a defined seasonal service life
- Geomembranes and outdoor sheet
- Woven raffia and outdoor textiles
- Injection-moulded outdoor articles
Back to products
A-FAUV0192Category D
Long-Term Outdoor UV Stabilizer (HALS)
HALS technology prevents photochemical degradation, yellowing, chalking and loss of tensile strength under intense UV.
Polyethylene REACH TDS
Logistics & Documentation
Plastic-Pallet Option · Import Documentation Support
- Lead Time: Depends on supplier availability, production schedule, shipping route and destination. Lead time and dispatch are confirmed with each quotation rather than published as a fixed figure.
- Packaging Option: Injection-molded plastic pallets available on request as an alternative to wooden pallets, subject to supplier capability and order size.
- Documentation Support: Import documentation support available. Available documents may include TDS, SDS, COA, origin documents and compliance declarations where applicable.
Additive identity
Values below are taken from the product record or the supplier technical data sheet held on file. Anything not shown here is confirmed in writing at quotation.
- Delivery form
- Masterbatch granule
- Compatible polymers
- HDPE, LDPE, LLDPE, PP
- Recommended dosage
- 1% – 5% (1–2% for 6–12 month service life; 4–5% for 4–5 year outdoor life)
- Active content
- UV absorber 6%, UV stabilizer 6%, antioxidant 3%
- UV / outdoor suitability
- Long-term outdoor exposure — UV absorber plus HALS stabilizer system
- Regulatory status
- REACH
- Technical source document
- TDS — PE/PP Anti-UV Masterbatch (FAUV0192-A/B), 15 June 2026
Additive family
Long-Term Outdoor UV Stabilizer (HALS) is supplied under this additive family — compare the full family before fixing on a grade.
Verified data
Only values printed on the supplier technical documents or recorded against this product are shown. Anything absent is confirmed at quotation rather than estimated here.
UV performance stated on supplier TDS
Product Name: PE/PP Anti-UV Masterbatch — Technical Data Sheet — PE/PP Anti-UV Masterbatch (FAUV0192-A/B). Service life must be validated on the finished article.
Dosage & let-down as stated by the supplier
| Item | Value | Document |
|---|---|---|
| Add Proportion | 1% – 5% | Technical Data Sheet — PE/PP Anti-UV Masterbatch (FAUV0192-A/B) |
| Recommended Add Proportion | 1 % – 5 % (depending on product requirements) | Technical Data Sheet — PE/PP Anti-UV Masterbatch (FAUV0192-A/B) |
| Important note — optimal dosage | Depends on base resin type, product thickness, color (darker colors typically require less), final application environment (latitude, altitude, pollution levels), desired lifespan, and processing conditions. | Technical Data Sheet — PE/PP Anti-UV Masterbatch (FAUV0192-A/B) |
| Important note — dosage balance | Insufficient addition may result in inadequate protection; excessive addition may increase cost and affect other properties (precipitation, migration, printability/adhesion). | Technical Data Sheet — PE/PP Anti-UV Masterbatch (FAUV0192-A/B) |
Dosage is a starting point from the supplier document. The working addition rate depends on your resin, part geometry and target, and is set on trial.
Technical & commercial reference
Long-term UV stabiliser (HALS) masterbatch — how buyers specify and compare offers
UV stabilisation is specified by required service life under a stated exposure, not by a percentage of additive. Two offers are comparable only when the exposure target and article thickness are stated.
Selection
How the right grade is chosen
- Required exposure life, normally expressed in kLy for the installation region
- Article thickness — thin sections need a higher additive concentration for the same life
- HALS chemistry choice where the article contacts sulfur- or halogen-containing agrochemicals, which can deactivate some HALS types
- Carrier resin compatibility with the base polymer
- Interaction with pigments and flame retardants already in the formulation
Specification
What to state in the enquiry
- Stabiliser family (HALS, UV absorber, or a combination) and active content
- Recommended let-down ratio for the stated exposure target
- Carrier resin and melt flow
- Any accelerated-weathering test data supplied with the grade
Procurement
Sourcing considerations
- Send the exposure target, article thickness, polymer and chemical environment with the enquiry
- Ask for the TDS of the offered grade with its dosage guidance
- Field service life claims should be traceable to a stated test method
- Grade, specification, documentation, packaging, availability and delivery terms are confirmed against supplier documentation with each quotation.
Comparison
Comparing competing offers
- Cost per year of service life rather than cost per kilogram
- Test method behind any weathering claim
- Compatibility with the rest of the additive package
General industry guidance. Grade, specification, documentation, packaging and delivery terms for Long-Term Outdoor UV Stabilizer (HALS) are confirmed against supplier documentation with each quotation. Request a quotation.
Document & COA status
- • TDS: Verified product TDS available below.
- • SDS: Safety data is subject to grade and supplier confirmation. One SDS does not necessarily apply to every grade or supplier.
- • COA: Certificate of Analysis is provided against the confirmed shipment, grade and batch. No stock, lead-time or regulatory claim is implied without written confirmation.
Technical Data Sheet
TDS · A-FAUV0192
Product form
Pellets (cylindrical, 2–4 mm)
Appearance
White
Carrier / matrix
Polyethylene compatible base resin
Key Physical & Chemical Properties
| Active ingredient | 20 – 40 % concentrate |
|---|---|
| Bulk density | 0.95 – 1.10 g/cm³ |
| Melt Flow Index (190 °C / 2.16 kg) | 5 – 12 g/10 min |
| Moisture content | ≤ 0.10 % |
| Recommended let-down ratio | 1 : 50 to 1 : 200 |
Recommended dosage
0.5 – 3.0 % by weight depending on target performance.
Processing temperature
190 – 260 °C
Packaging
25 kg multi-wall poly-woven bag with PE inner liner, 1000 kg FIBC, or 25 MT FCL bulk.
Shelf life
24 months from production date in unopened original packaging.
Storage
Store dry below 35 °C, away from direct sunlight, ignition sources and incompatible chemicals.
Target Applications
- Blown / cast film and lamination
- Injection molding of automotive and consumer parts
- Pipe, sheet, and profile extrusion
- Wire & cable jacketing where applicable
Key Features
- Long-lasting performance with low dosage
- Compatible with most polyolefin and engineering resins
- Excellent dispersion — no agglomerates
- REACH-registered active components
Safety Data Sheet · GHS / OSHA HazCom / WHMIS 2015
SDS · A-FAUV0192
Signal word
Not classified
Not classified as hazardous under OSHA HazCom 2012 / GHS / WHMIS 2015.
§ 1Identification▾
- Product code
- A-FAUV0192
- Product name
- Long-Term Outdoor UV Stabilizer (HALS)
- Product use
- Industrial raw material — Agricultural Liners, Building & Construction.
- Restrictions
- Industrial use only. Not for direct consumer sale unless explicitly labelled food/feed grade.
- Supplier
- Allzone Trading Corp.
- Address
- Ontario, Canada
- Technical contact
- technical@allzonetrading.ca · +1 (437) 297-6255
- Emergency
- CHEMTREC +1 800 424 9300 / CANUTEC +1 613 996 6666
§ 2Hazards Identification▾
- GHS classification
- Not classified as hazardous under OSHA HazCom 2012 / GHS / WHMIS 2015.
- Signal word
- Not classified
- Pictograms
- None required.
- Hazard statements
- No GHS hazard statements apply to this article in supplied form.
- Precautionary statements
- P210 Keep away from heat, sparks, open flames and hot surfaces.
§ 3Composition / Information on Ingredients▾
- Mixture
- Engineered polyethylene based long-term outdoor uv stabilizer (hals).
- Carrier
- Polyethylene compatible polymer.
§ 4First Aid Measures▾
- Inhalation
- Move to fresh air. Get medical advice if discomfort persists.
- Skin contact
- Wash with soap and water. Get medical advice if irritation persists.
- Eye contact
- Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do.
- Ingestion
- Rinse mouth. Do not induce vomiting. Seek medical advice if discomfort persists.
- Hot melt burns
- For pellet-form products processed at melt temperature: cool affected area with cold water. Do NOT peel solidified polymer from skin — seek medical attention.
§ 5Fire-Fighting Measures▾
- Suitable extinguishing media
- Water spray, dry chemical, CO2, foam.
- Unsuitable media
- None known.
- Special hazards
- Combustion may produce CO, CO2 and dense black smoke. Polymer melt drips during fire.
- PPE for firefighters
- Self-contained breathing apparatus (SCBA) and full protective gear.
§ 6Accidental Release Measures▾
- Personal precautions
- Wear PPE per Section 8. Avoid generating dust. Ventilate area.
- Environmental precautions
- Prevent entry into drains, waterways or soil. Notify authorities if significant release.
- Cleanup
- Sweep or vacuum spilled material into labelled container for recycling or disposal.
§ 7Handling & Storage▾
- Handling
- Handle in well-ventilated areas. Avoid generating dust. Use appropriate PPE.
- Storage
- Store dry below 35 °C, away from direct sunlight and ignition sources.
- Incompatible materials
- Strong oxidizers.
§ 8Exposure Controls / Personal Protection▾
- Engineering controls
- Local exhaust ventilation at material transfer and melt-processing points. Maintain dust below regional OEL.
- Respiratory protection
- Dust mask if fines / dust generated.
- Hand protection
- Heat-resistant gloves when handling molten polymer; cotton gloves for cold pellets.
- Eye protection
- Safety glasses with side shields; chemical splash goggles when handling powders or molten material.
- Body protection
- Long-sleeve work clothing. Full chemical apron for corrosive products.
- Exposure limits
- Follow nuisance-dust limits (10 mg/m³ total, 5 mg/m³ respirable).
§ 9Physical & Chemical Properties▾
- Physical state
- Solid pellets / powder
- Color
- White / off-white / pre-colored
- Odor
- Odorless to faint polymer odor
- pH (1 % solution)
- Not applicable (insoluble)
- Melting / decomposition
- Polymer melt 110 – 250 °C (matrix dependent)
- Flash point
- Not applicable (solid article)
- Solubility (water)
- Insoluble
- Density
- 0.9 – 2.2 g/cm³ depending on grade
§ 10Stability & Reactivity▾
- Stability
- Stable under normal storage and handling conditions.
- Conditions to avoid
- Excessive heat, ignition sources, prolonged UV exposure.
- Hazardous decomposition products
- CO, CO2, polymer fragment volatiles. Azodicarbonamide additionally releases NH3, N2.
§ 11Toxicological Information▾
- Acute oral toxicity (LD50, rat)
- Not classified (> 2000 mg/kg expected)
- Skin irritation
- Not classified for solid article in supplied form.
- Eye irritation
- Mechanical irritation possible from dust.
- Respiratory sensitization
- Not classified.
- Carcinogenicity
- Not classified.
- Mutagenicity / reproductive tox.
- No known effects based on current data.
§ 12Ecological Information▾
- Aquatic toxicity
- Not classified — substance is essentially inert in water.
- Persistence
- Persistent in environment — polymer fragments are not readily biodegradable.
- Bioaccumulation
- No bioaccumulation potential expected.
§ 13Disposal Considerations▾
- Product disposal
- Dispose in accordance with local, provincial, state and federal regulations. Recycle polymer fractions through certified plastic recyclers where possible.
- Packaging disposal
- Recycle empty bags / liners after thorough emptying.
- Waste codes
- Non-hazardous solid waste (EWC 07 02 13 typical).
§ 14Transport Information▾
- Status
- Not regulated for transport under DOT / IATA / IMDG / ADR / TDG.
§ 15Regulatory Information▾
- REACH (EC 1907/2006)
- All components registered or exempt. No SVHC listed above 0.1 % w/w.
- RoHS (EU 2011/65)
- Heavy metals < 1000 ppm (Pb, Hg, Cr⁶⁺) and < 100 ppm (Cd).
- Food contact
- Not intended for food-contact applications.
- WHMIS 2015 (Canada)
- Not classified as a hazardous product.
- TSCA / DSL
- All substances listed on US TSCA and Canadian DSL inventories.
§ 16Other Information▾
- Revision
- Rev. 2026-06-15 (representative industry-standard datasheet).
- Disclaimer
- Information provided in good faith based on current knowledge. No warranty expressed or implied. User is responsible for verifying suitability for end use and compliance with local regulations.
- Document
- SDS for A-FAUV0192
This SDS is provided as representative industry-standard guidance. For project-specific binding documentation, please request the formal current revision via the technical contact above.
Technical knowledge for Long-Term Outdoor UV Stabilizer (HALS)
Engineering and purchasing guidance written for this material — understand it, apply it, compare options, specify a grade, and fix production problems.
Foundation Articles
Application Guides
Comparison Articles
Buying Guides
Troubleshooting Guides
Related products
Materials commonly quoted alongside Long-Term Outdoor UV Stabilizer (HALS) by the same plants.
Polymer & Plastics
Thermal Anti-Oxidants & Process Stabilizers
Heat stabiliser — stops thermo-oxidative degradation during processing.
A-OX
Polymer & Plastics
Agricultural Film Additive Masterbatch
Polymer masterbatch — anti-Fog agents to reduce crop-burning condensation; Anti-IR barrier masterbatches to help retain night-time heat in greenhouses.
Agri-Sys
Polymer & Plastics
UV Stabilizers
Heat stabiliser — agricultural and greenhouse film
Industrial / plastics manufacturing
Sourcing Support
Need help sourcing this product?
Send us your product name, quantity, application, destination, and required documents. We will review your request and help compare available supply options.
Pricing and availability depend on quantity, destination, supplier confirmation and market conditions.
Continue the buyer journey — related grades, industry solutions, bulk supply, engineering tools and technical documents.
Industry & regional solutions
Bulk & container-direct supply
Continue learning
Engineering tools & documents
Ready to move forward? Send an RFQ — we usually acknowledge enquiries within one business day.