Back to products
NexusPlas F-TL4080Category C
Talc-Filled Reinforcement Masterbatch (High Stiffness)
Increases flexural modulus, dimensional stability and HDT. For under-the-hood parts, dashboard modules, appliance housings.
Polypropylene RoHS REACH TDS
Logistical Specifications & Compliance
Zero Customs-Risk · Plastic-Pallet Mandate
- Logistics Status: 24-to-48 Hour Local GTA Warehouse Dispatch.
- Packaging Standard: Shipped 100% exclusively on sterile, defect-free, injection-molded PLASTIC PALLETS.
- Compliance Highlight: 100% quarantine-exempt from CBSA/CFIA regulations — eliminating customs hold, wood-pest infestation, and particle-contamination risks of standard wooden pallets used by competitors.
Technical Data Sheet
TDS · NexusPlas F-TL4080
Product form
Pellets (3–4 mm)
Appearance
Off-white to white granules / powder
Carrier / matrix
PP/PE Matrix | Ultra-fine Platy Talc
Key Physical & Chemical Properties
| Mineral content | 75 ± 2 % mineral loading |
|---|---|
| Mean particle size (D50) | 2 – 4 μm |
| Bulk density | 1.55 – 1.85 g/cm³ |
| Brightness (Y, ISO 2470) | ≥ 94 % |
| Surface treatment | Stearic acid coated (1.0 – 1.5 %) |
| Moisture content | ≤ 0.20 % |
Recommended dosage
10 – 40 % depending on stiffness/cost target.
Processing temperature
170 – 230 °C
Packaging
25 kg multi-wall poly-woven bag with PE inner liner, 1000 kg FIBC, or 25 MT FCL bulk.
Shelf life
24 months from production date in unopened original packaging.
Storage
Store dry below 35 °C, away from direct sunlight, ignition sources and incompatible chemicals.
Target Applications
- PP woven bags and FIBC reinforcement
- Blown film cost-reduction / down-gauging
- Pipe, profile and conduit extrusion
- Paint, paper coating and architectural fillers
Key Features
- Improves stiffness, dimensional stability and HDT
- Reduces resin cost without sacrificing tensile strength
- Surface treatment ensures excellent matrix wetting
- Low abrasion on extrusion screws and dies
Safety Data Sheet · GHS / OSHA HazCom / WHMIS 2015
SDS · NexusPlas F-TL4080
Signal word
Warning
Not classified as hazardous. Generates nuisance dust during handling.
§ 1Identification▾
- Product code
- NexusPlas F-TL4080
- Product name
- Talc-Filled Reinforcement Masterbatch (High Stiffness)
- Product use
- Industrial raw material — Automotive Moldings.
- Restrictions
- Industrial use only. Not for direct consumer sale unless explicitly labelled food/feed grade.
- Supplier
- NexusPlas Polymer Solutions Inc.
- Address
- Ontario, Canada
- Technical contact
- technical@nexusplas.example · +1 (000) 000-0000
- Emergency
- CHEMTREC +1 800 424 9300 / CANUTEC +1 613 996 6666
§ 2Hazards Identification▾
- GHS classification
- Not classified as hazardous. Generates nuisance dust during handling.
- Signal word
- Warning
- Pictograms
- None required.
- Hazard statements
- May cause respiratory irritation by inhalation of dust (occupational exposure).
- Precautionary statements
- P261 Avoid breathing dust. P271 Use only outdoors or in a well-ventilated area. P280 Wear protective gloves and eye protection.
§ 3Composition / Information on Ingredients▾
- Mixture
- Engineered polypropylene based talc-filled reinforcement masterbatch (high stiffness).
- Carrier
- PP/PE Matrix | Ultra-fine Platy Talc
- Calcium carbonate (CAS 471-34-1) / Talc (CAS 14807-96-6)
- 70 – 85 % mineral filler in polymer carrier
§ 4First Aid Measures▾
- Inhalation
- Move to fresh air. Get medical advice if discomfort persists.
- Skin contact
- Wash with soap and water. Get medical advice if irritation persists.
- Eye contact
- Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do.
- Ingestion
- Rinse mouth. Do not induce vomiting. Seek medical advice if discomfort persists.
- Hot melt burns
- For pellet-form products processed at melt temperature: cool affected area with cold water. Do NOT peel solidified polymer from skin — seek medical attention.
§ 5Fire-Fighting Measures▾
- Suitable extinguishing media
- Water spray, dry chemical, CO2, foam.
- Unsuitable media
- None known.
- Special hazards
- Combustion may produce CO, CO2 and dense black smoke. Polymer melt drips during fire.
- PPE for firefighters
- Self-contained breathing apparatus (SCBA) and full protective gear.
§ 6Accidental Release Measures▾
- Personal precautions
- Wear PPE per Section 8. Avoid generating dust. Ventilate area.
- Environmental precautions
- Prevent entry into drains, waterways or soil. Notify authorities if significant release.
- Cleanup
- Sweep or vacuum spilled material into labelled container for recycling or disposal.
§ 7Handling & Storage▾
- Handling
- Handle in well-ventilated areas. Avoid generating dust. Use appropriate PPE.
- Storage
- Store dry below 35 °C, away from direct sunlight and ignition sources.
- Incompatible materials
- Strong oxidizers.
§ 8Exposure Controls / Personal Protection▾
- Engineering controls
- Local exhaust ventilation at material transfer and melt-processing points. Maintain dust below regional OEL.
- Respiratory protection
- Dust mask if fines / dust generated.
- Hand protection
- Heat-resistant gloves when handling molten polymer; cotton gloves for cold pellets.
- Eye protection
- Safety glasses with side shields; chemical splash goggles when handling powders or molten material.
- Body protection
- Long-sleeve work clothing. Full chemical apron for corrosive products.
- Exposure limits
- Follow nuisance-dust limits (10 mg/m³ total, 5 mg/m³ respirable).
§ 9Physical & Chemical Properties▾
- Physical state
- Solid pellets / powder
- Color
- White / off-white / pre-colored
- Odor
- Odorless to faint polymer odor
- pH (1 % solution)
- Not applicable (insoluble)
- Melting / decomposition
- Polymer melt 110 – 250 °C (matrix dependent)
- Flash point
- Not applicable (solid article)
- Solubility (water)
- Insoluble
- Density
- 0.9 – 2.2 g/cm³ depending on grade
§ 10Stability & Reactivity▾
- Stability
- Stable under normal storage and handling conditions.
- Conditions to avoid
- Excessive heat, ignition sources, prolonged UV exposure.
- Hazardous decomposition products
- CO, CO2, polymer fragment volatiles. Azodicarbonamide additionally releases NH3, N2.
§ 11Toxicological Information▾
- Acute oral toxicity (LD50, rat)
- Not classified (> 2000 mg/kg expected)
- Skin irritation
- Not classified for solid article in supplied form.
- Eye irritation
- Mechanical irritation possible from dust.
- Respiratory sensitization
- Not classified.
- Carcinogenicity
- Not classified.
- Mutagenicity / reproductive tox.
- No known effects based on current data.
§ 12Ecological Information▾
- Aquatic toxicity
- Not classified — substance is essentially inert in water.
- Persistence
- Persistent in environment — polymer fragments are not readily biodegradable.
- Bioaccumulation
- No bioaccumulation potential expected.
§ 13Disposal Considerations▾
- Product disposal
- Dispose in accordance with local, provincial, state and federal regulations. Recycle polymer fractions through certified plastic recyclers where possible.
- Packaging disposal
- Recycle empty bags / liners after thorough emptying.
- Waste codes
- Non-hazardous solid waste (EWC 07 02 13 typical).
§ 14Transport Information▾
- Status
- Not regulated for transport under DOT / IATA / IMDG / ADR / TDG.
§ 15Regulatory Information▾
- REACH (EC 1907/2006)
- All components registered or exempt. No SVHC listed above 0.1 % w/w.
- RoHS (EU 2011/65)
- Heavy metals < 1000 ppm (Pb, Hg, Cr⁶⁺) and < 100 ppm (Cd).
- Food contact
- Not intended for food-contact applications.
- WHMIS 2015 (Canada)
- Classified — Signal word: Warning.
- TSCA / DSL
- All substances listed on US TSCA and Canadian DSL inventories.
§ 16Other Information▾
- Revision
- Rev. 2026-06-15 (representative industry-standard datasheet).
- Disclaimer
- Information provided in good faith based on current knowledge. No warranty expressed or implied. User is responsible for verifying suitability for end use and compliance with local regulations.
- Document
- SDS for NexusPlas F-TL4080
This SDS is provided as representative industry-standard guidance. For project-specific binding documentation, please request the formal current revision via the technical contact above.
Need a sample or formal documentation?
Our technical desk responds within 48 hours with TDS, SDS and lab-trial samples.